According to the size of the house, the construction line is made, in order to facilitate the accuracy of the vertical laid, ensure that the door sleeve can be installed smoothly, it is necessary to use the theodolite to hit the vertical control line of the two faces of the large corner. Then, the pre-arranged support is installed on the upper line and is to be supported on the top of the low-layer dead plate to be installed.

When the vertical line and the horizontal line are popped up, then the installed stone position line and the block line are applied according to the design drawings and actually populated the installed stone. The material is different means that the installation steps and installation processes are also different.

Note that the base bracket that is installed is cleaned up. Pay attention to the position of the component and trenches when installing the hierarchical sheet. Before installing the door of the house, it is necessary to ensure that the surface of the stone must meet the design requirements, and it should be noted that the six faces of the stone must be drunk, which is to prevent alkalization and waterproof.

When the gantry is installed, the level is adjusted, then the verticality is adjusted, it is to adjust the wall void of the stainless steel connector on the panel, until the panel is in a vertical state.At present, villas are developing in a diversified direction, while different types of door covers such as stainless steel, wood, marble have their own characteristics.

Pay attention to the connection between the branches. China Panoramic Elevators Of course, it is necessary to ensure that the stone color installed on the same surface is the same, and the stone is to be numbered in the order of the drawings and block. After installation, you can ensure that the upper and lower surfaces mounted on the marble door sleeve can be on the same level

Megosztás a facebookon

The safety is applied to the bottom of the car. Once the home of the household, once the system is cut, it will automatically identify the load status of the current car. It is a device that is close to the brake pedal. Automatically run to the near floor, open the car door, release the user, wait for the check in the long-term opening of the car door.Household can't rise again, but at this time, the car is able to decline, the car is slippery, the limit power switch is automatically calibrated.

The speed limiter is a mechanical device that tests the rate of the car. When home uses home to operate the upper limit area, the limit power switch will work.Power-saving self-help function: home operation requires power, not running in standby, there is almost no electricity consumption, and the usual electricity is very small. Extreme maintenance: Household installation has a limit power switch.

Once the family is housed, the galvanized steel wire rope is broken, the car is extremely The drop rate exceeds the larger speed limit rate set by the limiter, and the limiter will pinch the galvanized steel wire rope and drive the safety pliers to lock the car to avoid the car again to ensure the safety of customers. .

With the development of society and various high-end villa accommodation, everyone's dependence on household is growing. An installation is installed in the home, and it is also necessary to take into account its cost performance.Rope break protection function: Household host room installed limited speed and safety pliers. This is able to calibrate fully automatically.

Mainly, its security, villa elevators Suppliers home security performance is good to see these four features, what four features? It is set at a larger speed limit rate. Overweight maintenance: Once the load weight of the home exceeds itself, alert will issue an alert and will not run, and always keep the door to ensure the security of the user.

Megosztás a facebookon

Therefore, small villa elevator installation must be carried out after the renovations are completed. If the elevator has been installed before the house renovation, so a lot of dust generated in the process of renovation will enter the elevator, on the one hand difficult to clean, more important is the fine dust into the interior of the elevator structure will affect the normal operation of the elevator, the elevator shorten life.

This is especially need to pay attention when cutting small villa elevator floor installation, many times owners and construction team communication is not good, it is easy to be the case: the same each floor cut hole size, but not through the vertical space, so small villa elevator can not be installed, the need for secondary construction, waste of time and a waste of manpower. The hoistway small elevators without the overhead required to reduce some more, as long as the above can be 2400mm.

It is recommended that the car is listed in the park, preventing the alarm to save the faultist.Third, safety measures 1. 3: Recommended 150-400kg of load capacity, the size of the car is 0. Well position and space.The villa will have a installation process after purchasing, many people don't know what to install, what is the villa elevator installation including? Use the open door width in the well width, and the top height is highly reversed. Second, the ground pit and the top layer.

General small bottom pit 350mm, no pit can be used to borrow the bottom pit with decorative ground, and then the elevator raises passenger lift Factory a step. The passenger is not allowed to save the passengers, the family is different, and it is possible to make a long sleepy person.The middle of the stairs, the wall corner, plug-in can, and the center is not blocking the channel. Fourth, the speed home villa elevator is not very high because of the family floor, there is an old man, children and the potential for the use, and the speed is not too fast. Add self-help measures and procedures.

The top level is greater than 2600mm, and the car is 2200mm high. Automatic, manual door must have an electrical interlock function to prevent open the door and the elevator does not pull the door. 2: The elevator without the door of the car must install the lighting door to ensure the risk of friction, collision, and extrusion. 

Megosztás a facebookon